Mitutoyo Test & Measuring Instruments Online

The End of The Main Scale is Hook Shaped to

Fine Adjustment Models are Available

Fine Adjustment Models are Available

The End of The Main Scale is Hook Shaped to

Supplied in Fitted Carton

Specially Designed for the Zero Point Setting of Screw Thread

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

The Radial Displacement of Split-Ball Contact is Converted to Axial...

These Bore Gages Measure Diameters of Small Holes

The Radial Displacement of Split-Ball Contact is Converted to Axial...

These Bore Gages Measure Diameters of Small Holes

Thimble can be Set to Zero at Any Position by

Specially Designed to Measure Tire Tread Depth

The Origin Point, Once Set, for The Life of The

Auto Power on & off Function

Measurement Data Output Function on is Available with a Water-Resistant

Heat-Insulated Frame, Tapered (on the Anvil Side) for Hard-To-Reach Places

Supplied in a Fitted Plastic Case & a Ratchet Stop

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

Extension Rods (Optional) can be Attached for Measuring Deep Holes

Interchangeable Anvil is Attached to a Micrometer Head for Accurate

Alarm: Low Voltage, Counting Value Compositi on Error

Non-Slip Grip Finish & with SPC Output

with Ratchet Stop for Constant Force

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

Digimatic Output Port Enables Inclusion in a Statistical Process Control

Equipped with Digital Display & Output

Ratchet Stop for Exact Repetitive Reading

Hammertone, Baked-Enamel-Finished Frame

Supplied in Fitted Plastic Case

The Carbide-Tipped Jaws Facilitate Fine Scribing On Workpiece with Depth

Inside & Outside Measurements can Be Directly Read From The

With Fine Adjustment Carriage to Feed The Slider

Carbide Tipped Measuring Face

Ratchet Stop for Constant Force

Wide Measuring Range with in Terchangeable Anvils

Supplied with Zero-Setting Standards Bar for Each Range

Carbide Tipped Measuring Face

Ratchet Stop for Constant Force

Improved Finish on Sliding Surfaces for Longevity

Supplied in Fitted Plastic Case

The Rod Length Can Be Adjusted in 1 inch Or

Supplied in Fitted Plastic Case

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

The Small Vernier Face Angle (14 Deg) Provides Easy Reading

Lock Screw for Holding The Sliding Jaw Position

The Jaws Have Round Measuring Faces for Accurate Id Measurement

Inside & Outside Measurements can Be Directly Read From The

Optional Wider Extension Base are Available

Easier & Faster Reading of Dial

Data Hold Unit (959143) is Optional

Thumb Roller included only on Caliper Up to & including

Supplied with Zero-Setting Standards Bar for Each Range

Wide Measuring Range with in Terchangeable Anvils

Easy Reading Due to the Large Thimble Diameter

V-Anvils & Conical Spindle Tips for Screw Thread Measurement

with Ratchet Stop for Constant Force

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

Water & Dust Protection & with SPC Output (Series 324)

These Bore Gages Measure Diameters of Small Holes

The Radial Displacement of Split-Ball Contact is Converted to Axial...

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

60 Degree or 55 Degree V-Anvil & Conical Spindle (interchangeable)

Measure Root Tangent Length of Spur Gears & Helical Gears

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

Ratchet Stop for Constant force

Measuring Rod Clamp

Carbide Tipped Measuring Face