Mitutoyo Products

Auto Power on & off Function

Measurement Data Output Function on is Available with a Water-Resistant

Grip is Large & Hollow to Reduce Effect of Body

Carbide-Contact Point Ensures High Durability & Wear Resistance

Fast & Accurate Method of Thread Measuring Available for use

Fast & Accurate Method of Thread Measuring Available for use

Direct Readout of Id Measurements From The LCD

Preset Function for Setting A Desired Starting Point

Supplied in Fitted Plastic Case

Specially Designed for Center to Center Distance Measurements on The

Measure ID at Position Close to the Bottom of Blind

Carbide-Contact Point Ensures High Durability & Wear Resistance

Ratchet Stop for Exact Repetitive Reading

Hammertone, Baked-Enamel-Finished Frame

with Ratchet Stop for Constant Force & SPC Output (Series

Measure Root Tangent Length of Spur Gears & Helical Gears

Thumb Roller included only on Caliper Up to & including

Carbide-Tipped Jaw-Type Caliper are Also

Measure ID at Position Close to the Bottom of Blind

Carbide-Contact Point Ensures High Durability & Wear Resistance

Measure ID at Position Close to the Bottom of Blind

Grip is Large & Hollow to Reduce Effect of Body

Measure ID at Position Close to the Bottom of Blind

Grip is Large & Hollow to Reduce Effect of Body

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

with Ratchet Stop for Constant Force & SPC Output (Series

Specially Designed for Center to Center Distance Measurements on The

Hole Diameter Should Be in The Range of 1.5mm -

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

Water & Dust Protection (Series 395) with SPC Output &

Carbide-Contact Point Ensures High Durability & Wear Resistance

Measure ID at Position Close to the Bottom of Blind

Supplied in Fitted Plastic Case Except 40 inch/ 1000mm Supplied

A Fine-Adjustment Carriage Type is Available

Heat Insulating Handle to Prevent Expansion Due to Body Temperature

Zero Point Setting of Outside Micrometers

Flat & Lapped Measuring Faces

Zero Point Setting of Outside Micrometers

Preset, Zero-Setting, Power on & off, Data Hold, Data Output,

Alarm: Low Voltage, Counting Value Composition on Error

Fine Adjustment Models are Available

Optional Wider Extension Bases are Available

The Zirconia-Based Ceramic Cera Measuring Blocks are Corrosion

The Cera Caliper Checker is Designed to inspect Vernier, Dial

Optional Wider Extension Bases are Available

The End of The Main Scale is Hook Shaped to

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

Supplied in Fitted Carton

Specially Designed for the Zero Point Setting of Screw Thread

60 Degree or 55 Degree V-Anvil & Conical Spindle (interchangeable)

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

with Ratchet Stop for Constant force

Supplied in Fitted Plastic Case

Supplied in Fitted Plastic Case

with Ratchet Stop for Constant Force

Lock Screw for Dial Bezel & for Holding The Sliding

Improved Finish on Sliding Surfaces for Longevity

New Face for Improved Readability

Supplied in Fitted Plastic Case

Water & Dust Protection & SPC Output (Series 326)

60 Degree or 55 Degree V-Anvil & Conical Spindle (interchangeable)

incorporates Absolute Measurement System

Data Output Function

Bottom Surface of The Base is Hardened Ground & Lapped

Designed with A Back-Plunger Type Dial indicator for Upward Facing

Wide Probing Range is Available with The Supplied Extension Rod

Bottom Surface of The Base is Hardened Ground & Lapped

with Ratchet Stop for Constant Force

V-Anvils & Conical Spindle Tips for Screw Thread Measurement

Carbide Ball Contact Point for Durability

Interchangeable Anvil is Attached to a Micrometer Head for Accurate

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

with Ratchet Stop for Constant Force

Measures Over-Pin Diameter of Gears with Precision Steel (Carbide) Ball-Tipped

with Ratchet Stop for Constant Force

Extension Rods (Optional) can be Attached for Measuring Deep Holes

Wide Measuring Range with Sub-Anvils