Mitutoyo Products

The End of The Main Scale is Hook Shaped to

Fine Adjustment Models are Available

Fine Adjustment Models are Available

Optional Wider Extension Bases are Available

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

These Bore Gages Measure Diameters of Small Holes

The Radial Displacement of Split-Ball Contact is Converted to Axial...

The Radial Displacement of Split-Ball Contact is Converted to Axial...

These Bore Gages Measure Diameters of Small Holes

Thimble can be Set to Zero at Any Position by

Specially Designed to Measure Tire Tread Depth

The Origin Point, Once Set, for The Life of The

A Nonslip Surface is Employed for the Frame Cover &

Auto Power on & off Function

Supplied in a Fitted Plastic Case & a Ratchet Stop

Heat-Insulated Frame, Tapered (on the Anvil Side) for Hard-To-Reach Places

Supplied in Fitted Carton

Specially Designed for the Zero Point Setting of Screw Thread

Interchangeable Anvil is Attached to a Micrometer Head for Accurate

Wide Measuring Range with Sub-Anvils

Origin-Set, Zero & ABS, Data Hold, Data Output, inch &...

Alarm: Low Voltage, Counting Value Compositi on Error

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

with Ratchet Stop for Constant Force

Equipped with Digital Display & Output

Digimatic Output Port Enables Inclusion in a Statistical Process Control

Ratchet Stop for Exact Repetitive Reading

Hammertone, Baked-Enamel-Finished Frame

Supplied in Fitted Plastic Case

The Carbide-Tipped Jaws Facilitate Fine Scribing On Workpiece with Depth

The Jaws Have Round Measuring Faces for Accurate Id Measurement

With Fine Adjustment Carriage to Feed The Slider

Ratchet Stop for Constant Force

Carbide Tipped Measuring Face

Supplied in Fitted Wooden Case & with SPC Output (Series

Wide Measuring Range with in Terchangeable Anvils

Ratchet Stop for Constant Force

Carbide Tipped Measuring Face

Improved Finish on Sliding Surfaces for Longevity

Lock Screw for Dial Bezel & for Holding The Sliding

4mm interchangeable Rods, with Lapped Measuring & Provide A Wide

The Rod Length Can Be Adjusted in 1 inch Or

Specially Designed for the Zero Point Setting of Screw Thread

Supplied in Fitted Carton

Lock Screw for Holding The Sliding Jaw Position

Carbide-Tipped Jaw-Type Caliper are Available

Inside & Outside Measurements can Be Directly Read From The

With Fine Adjustment Carriage to Feed The Slider

Easier & Faster Reading of Dial

Base & Measuring Faces are Hardened & Micro-Lapped

Carbide-Tipped Jaw-Type Caliper are Also

Thumb Roller included only on Caliper Up to & including

with a Ratchet Stop for Constant force

Supplied with Zero-Setting Standards Bar for Each Range

Easy Reading Due to the Large Thimble Diameter

V-Anvils & Conical Spindle Tips for Screw Thread Measurement

with Ratchet Stop for Constant Force

Water & Dust Protection & with SPC Output (Series 324)

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

The Radial Displacement of Split-Ball Contact is Converted to Axial...

These Bore Gages Measure Diameters of Small Holes

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

60 Degree or 55 Degree V-Anvil & Conical Spindle (interchangeable)

Non-Slip Grip Finish & Supplied in Fitted Plastic Case

with Ratchet Stop for Constant Force

Carbide-Tipped Measuring Rod Model is Available

Measuring Rod Clamp

Carbide Tipped Measuring Face